prv6 www.vishay.com vishay sfernice revision: 04-jul-17 1 document number: 51035 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fully sealed potentiometer cermet or conductive plastic features ? prv6s high power rating 1.5 w at 70 c (cermet) ? prv6a 0.75 w at 70 c (conductive plastic) ? tests according to cecc 41000 or iec 60393-1 ?low cost ? fully sealed and panel sealed ? compatible rv6 (mil r 94) ? mechanical endurance 50 000 cycles ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 quick reference data multiple module no switch module n/a detent module n/a special electrical laws a: linear, l: logarithmic, f: reverse logarithmic sealing level ip 67 lifespan 50k cycles dimensions in millimeters (inche s) 0.5 mm ( 0.02") prv6 style a and s prv6 style b and c shaft diameter 3 mm (0.118") bushing a-b-c shaft diameter 3.17 mm (0.125") bushing a-b-c shaft diameter 4 mm (0.157") bushing h-i (not panel sealed) leads x = pcb pins leads y = solder lugs 9.5 (0.374) 5 (0.200) 0.8 (0.031) 12.1 (0.476) 5 (0.200) 0.8 (0.031) aa ab aj ? 3 (0.118) ba bb bj ? 3.17 (0.125) b = s ee bu s hing table 0.8 (0.031) ea eb ej ? 4 (0.157) 5.08 (0.200) 5.08 (0.200) 2.15 (0.085) ? 12.7 (0.50) 0.8 x 0.3 (0.031 x 0.012) 2.4 (0.094) 0.8 (0.031) 0.5 (0.020) 5.08 (0.200) 5.08 (0.200) 2.15 (0.085) ? 12.7 (0.50) 1.6 x 0.3 (0.063 x 0.012)
prv6 www.vishay.com vishay sfernice revision: 04-jul-17 2 document number: 51035 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 electrical specifications prv6s, prv6b prv6a, prv6c resistive element cermet conductive plastic electrical travel 270 15 resistance range linear taper (a) 20 to 10 m 1 k to 1 m non-linear taper (f-l) 470 to 1 m 470 to 500 k ( 20 %) taper tolerance standard 20 % 20 % on request 10 %, 5 % 10 % (1 k to 100 k ) circuit diagram power rating at 70 c linear 1.5 w at 70 c 0.75 w at 70 c other tapers 0.75 w 0.4 w power rating chart temperature coefficient (typical) 150 ppm/c 500 ppm/c limiting element voltage 350 v contact resistance variation (crv) 2 % or 3 end resistance (typical) 1 dielectric strength (rms) 1750 v rms insulation resistance (500 v dc ) 10 6 m f a l 90 % v s v e % 25 15 electrical travel 270 mechanical travel 300 50 % 20 % 10 % 15 50 75 a c b cw (2) (3) (1) 0 40 125 0.75 0 ambient tempera ture in degrees celsius p o wer in watt 70 60 20 100 80 prv6s, prv6b linear taper 0.4 1.50 prv6s, prv6b non-linear taper prv6a, prv6c linear taper prv6a, prv6c non-linear taper
prv6 www.vishay.com vishay sfernice revision: 04-jul-17 3 document number: 51035 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? nothing stated herein shall be construed as a guarantee of quality or durability mechanical specifications mechanical travel 300 5 operating torque (ncm (oz.in.)) 0.5 to 2 (0.7 to 3) end stop torque (max. ncm (lb.in.)) 35 (3) tightening torque (max . ncm (lb.in.)) 150 (13) environmental specifications prv6s, prv6b prv6a, prv6c temperature range -55 c to +125 c -40 c to +125 c climatic category 55/125/56 40/125/56 sealing fully sealed contai ner; ip67 and panel sealed performances tests conditions typical values and drifts r t / r t (%) r 1-2 / r 1-2 (%) other electrical endurance 1000 h at rated power 90'/30' - temperature 70 c 1 % crv < 3 % rn climatic sequence phase a dry heat 100 c phase b damp heat phase c cold -55 c phase d damp heat 5 cycles 0.5 % 1 % damp heat, steady state 56 days 0. 5 % 1 % insulation resistance: > 10 4 m change of temperature 5 cycles, -55 c to +125 c 0.5 % mechanical endurance 50 000 cycles 3 % crv < 2 % rn shock 50 g at 11 ms 3 successive shocks in 3 directions 0.1 % 0.2 % vibration 10 hz to 55 hz 0.75 mm or 10 g during 6 h 0.1 % 0.2 % standard resistance element data standard resistance values prv6s and prv6b with linear taper prv 6s and prv6b with non-linear taper max. power at 70 c max. working voltage max. wiper current max. power at 70 c max. working voltage max. wiper current wv ma wv ma 20 1.5 5.48 274 50 1.5 8.66 173 100 1.5 12.2 122 200 1.5 17.3 87 500 1.5 27.4 55 0.75 19.4 39 1k 1.5 38.7 38.7 0.75 27.3 27.4 2k 1.5 54.8 27.4 0.75 38.2 19.3 5k 1.5 86.6 17.3 0.75 61.2 12.2 10k 1.5 122.5 12.2 0.75 87 8.7 20k 1.5 173 8.26 0.75 122 6.1 50k 1.5 274 5.65 0.75 194 3.9 100k 1.22 350 3.5 0.75 273 2.74 220k 0.61 350 1.75 0.61 350 1.75 500k 0.25 350 0.70 0.25 350 0.7 1m 0.12 350 0.35 0.12 350 0.35 2m 0.06 350 0.17 5m 0.025 350 0.070 10m 0.012 350 0.035
prv6 www.vishay.com vishay sfernice revision: 04-jul-17 4 document number: 51035 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 marking ? vishay trademark ? part number ? manufacturing date code ?terminal: 1 packaging ? box of 15, 20, 25, or 50 pieces, co de b12, b15, b17, or b25, depend ing of body and shaft construction options special features panel sealing except for dia. 4 mm shaft, an o.ri ng is supplied with the potentiometer. this o.ri ng should be placed into the groove of the body and ensures the panel sealing. for dia. 4 mm shaft please see note p in ordering information. shaft locking shafts shaft lengths are measured from the mounting face to the free end of the shaft. special shafts are available if the customer supplies a drawing. the shaft slot is aligned to the wiper within 10. hardware nuts, washer and o.ring are separa tely supplied (not mounted on th e potentiometer), in a small bag placed in the packaging. locating peg except for dia. 4 mm shaft, the pote ntiometers are delivered with 2 o pposite locating pegs orientated at 45.these 2 pegs can be easily broken-off by the customer. on request, the orientation of the pegs can be at 30 instead of 45.
prv6 www.vishay.com vishay sfernice revision: 04-jul-17 5 document number: 51035 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) not standard, spec ial manufacturing locating peg code bushing old code a l r 0 a6xx x (1) b61x x x (1) c62 x x x (1) d61hx x x (1) e62hx x x (1) h6q x i 61q x j6qp x k 61qp x s 61qh x s61qph x ordering information (part number) model style bushing locating peg shaft leads packaging resistance code/ tolerance/ taper or special prv6 s = standard a = audio b = body length c = audio and body length ?l old codes 0 = without a = 45 l = 30 r = 180 round (see locating peg table above) ?l old codes x = pcb pins (old code w) y = solder lugs depending of body and shaft construction: b12 = box 15 pcs b15 = box 20 pcs b17 = box 25 pcs b25 = box 50 pcs resistance: from 200 = 20 to 106 = 10 m for linear cermet tolerance: standard m = 20 % on request k = 10 % or j = 5 % taper: a, l, f or special code given by vishay a1/4 1/4 6 aa 3 9.5 k b 1/4 3/8 61 ab 3 12.5 m c1/4 1/2 62 aj 3 22 r d 1/4 3/8 61h ba 1/8 9.5 ck e 1/4 1/2 62h bb 1/8 12.5 cm h 7 6.5 6q bg 1/8 16 cd i 7 9.5 61q bj 1/8 22 cr j7 6.5 6qp ea4 9.5 e k 7 9.5 61qp eb 4 12.5 f s 7 9.5 61qh ej 4 22 g s 7 9.5 61qph ap custom shaft all are slotted part number description (for information on ly using old codes) prv s 61 w cd 5k 20 % a bo e3 model bushing leads special shaft value to lerance taper special packaging special ap n o special lead finish related documents application notes potentiometers and trimmers www.vishay.com/doc?51001 guidelines for vishay sfernice resistive and inductive components www.vishay.com/doc?52029 6bba g 17 b rv 02 5 p ma x b
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
